- Product: SpeedyBee SB-F4V3-50-STACK
- MCU: STM32F405
- IMU(Gyro): BMI270
- USB Port Type: Type-C
- Barometer: Built-in
- OSD Chip: AT7456E chip
Flight Controller & Accessories
SpeedyBee SB-F4V3-50-STACK
- Product: SpeedyBee SB-F4V3-50-STACK
- MCU: STM32F405
- IMU(Gyro): BMI270
- USB Port Type: Type-C
- Barometer: Built-in
- OSD Chip: AT7456E chip
₹7,895.00 ₹8,895.00
Related products
-
Flight Controller & Accessories
2.4G 4CH Receiver Compatible with D8 Receiver w/ PWM Output
- Channel: 4CH
- Weight: 2.2g
- Resolution: 1024
- PWM Output: Yes
- Operating Voltage: 3.5-10V
- Current: 50MA
- Antenna Length: 100mm
- Control Range: >500M+
- Compatibility: Compatible with Frsky X9D (D8 Mode), XJT (D8 Mode), DJT, DFT, DHT
SKU: n/a -
Flight Controller & Accessories
OpenPilot CC3D EVO Flight Controller STM32 for RC Drone FPV Racing
-30%
Flight Controller & AccessoriesOpenPilot CC3D EVO Flight Controller STM32 for RC Drone FPV Racing
CC3D Flight Controller Hardware Features
Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac, and Linux.
Direct high-speed USB support with no drivers required, a truly plug-and-play device.
Spektrum satellite receiver support.
Futaba S-BUS hardware support.
Innovative Flexi-port technology for superior port flexibility.
4Mbits on-board EEPROM for configuration storage.Note: Please don’t flash/Update the Default firmware. Updated or new firmware may cause a problem of connectivity with PC/Laptop.
Software for configuration: Openpilot
You can also use Software for configuration: Librepilot
Flexiport
CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C
and a single serial port or dual serial ports, according to your connectivity needs.Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally, for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with a bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.The OpenPilot project, whist still young, it trying to make Open Source much more user-friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!
Sensors and Components
3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.
Simultaneous support for multiple receivers.
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
Onboard USB connectivity for easy configuration.
USB and serial telemetry and configuration
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500HzPackage included:
1 x CC3D EVO Flight Controller And CablesSKU: n/a -
Flight Controller & Accessories
ARDUCOPTER APM 2.8 Flight Control Board for RC Multi Rotor Drone
-49%
Flight Controller & AccessoriesARDUCOPTER APM 2.8 Flight Control Board for RC Multi Rotor Drone
This is the new APM 2.8 module. The sensors are exactly the same as with APM2.6, this version is ideal for use with multi-copters and rovers. The APM 2.8 is a complete open source autopilot system and the bestselling technology on the prestigious 2012 Outback Challenge UAV competition.
It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors. This revision of the board is designed for vehicles (especially multi-copters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. On fixed-wing aircraft, it’s often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference.
APM 2.8 has an onboard compass so this is designed to be used with the 3DR uBlox GPS with Compass so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
Features:
- Arduino Compatible
- Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively.
- Built-in compass
- Includes 3-axis gyro, accelerometer, and magnetometer, along with a high-performance barometer
- Straight Needle
- One of the first open-source autopilot systems to use Invensense’s 6 DOF Accelerometer/Gyro MPU-6000.
- Onboard 4 MegaByte Data flash chip for automatic data logging
- Optional off-board GPS, uBlox LEA-6H module with Compass.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
Package Include:
- 1 x APM 2.8 Flight Control Board
- 1 x Set of Female to Female jumper Cables
Note: Ardupilot and Arducopter Both identical.
SKU: n/a
There are no reviews yet.